FR4 94V0 Printed Circuit Board PCB

Product Details


Introduction

Printed circuit board using FR4 as core material will be named as "FR4 PCB". PCB is used to mechanically support and electrically connect electronic components using conductive pathways, tracks or signal traces etched from copper clad laminate substrate.


Specifications of FR4 PCB

Material

FR-4

Finish Board Thickness

0.2 mm-6.00mm(8mil -126mil)Surface Finish

Surface Finish

Gold finger, Immersion Gold, Plating

Gold, HASL, OSP

Shape

Routing、Punch、V-cut、Chamfer

Surface Treatment

Solder Mask(black, green, white, red, blue, thickness>=12um, Block,

BGA)

Silkscreen(black, yellow, white)

Peel able-mask(red, blue, thickness>=300um)

Copper Thickness

1/2 oz min; 12oz max

Min Trace Width & Line Spacing

0.075mm /0.075mm (3mil/3mil)

Min Hole Diameter for CNC Drilling

0.1mm(4mil)

Min Hole Diameter for Punching

0.6mm(35mil)

Hole Position

+/-0.075mm(3mil) CNC Drilling

Conductor Width(W)

+/-0.05mm(2mil) or +/-20% of original

Hole Diameter(H)

PTHL:+/-0.075mm(3mil)

Non PTHL:+/-0.05mm(2mil)

Conductivity

<50ohm


Our service

· PCB Copy and clone

· Components sourcing and purchasing

· Quick prototyping

· PCB Fabrication

· Special PCB

· PCB Assembly

· 100%Test: AOI, In-Circuit Test (ICT), Functional Test (FCT)

· Custom clearance for material importing and product exporting


Classification of FR4 Printed Circuit Board

According to number of copper trace layers, FR4 printed circuit board is normally divided into following types:

Single Sided (S/S), or Single layer;

Double Sided(D/S), or double layer, 2Layers, 2L;

Four Layers (4L), Six Layers (6L), Eight Layers (8L), Ten Layers (10L)

Board with more than 10L

In fact, for board more than four layers, people will named it "Multi-layer PCB" According to that standard, there're only three types of PCB: Single, Double and Multi-layers.

If divide the board according to manufacturing technology, major based on hole diamter size, it'll divid into two types:

Normal through hole (diameter >=0.20mm (8mil)

HDI(diameter <=0.15mm (6mil)

According to copper thickness, it can be divided into

Normall copper: copper thickness: 0.5 OZ, 1.0 OZ, 2.0 OZ,

Heavy copper: copper thickness: >= 3 OZ

According to core material, it can be divided into

Rigid FR4 PCB: Only FR4, it is rigid for whole board;

Rigid-flex circuits: Rigid FR4 plus flexible circuits;

According to Tg value of FR4, it can be divided into

Normal Tg: Value 130, 135, 140;

High Tg: Value 170, 180;

According to radio frequency (RF) level of PCB, it can be divided into

Normal: < 300 Mhz

High Radio Frequency: 300MHz ~ 3GHz,or even bigger

According to board thickness, it can be divided into

Normal: >=0.30mm

Extra Thin: 0.10~0.30mm;



Workshop

 


FAQ

1.How do we keep our prices low?

A:We are PCB manufacturer and also have relationships with a large number of component manufacturers and can find the best source of material to consistently save your cost, meet your development schedule, fulfill your prototyping or mass production needs.

 

2.What is Test NRE?

A:The Test NRE is a one-time "non recurring expense" for electrical test. This charge is optional but when paid, all circuit boards will be tested each and every time that part number and revision is ordered without additional charge.

 

3.When do you pay a tooling NRE fee for my printed circuit board?

A:You will only pay a Tooling charge if you go directly to Production (Custom Spec) without having ordered a Prototype(Standard Spec) as a first step. We do not charge Tooling for Prototype (Standard Spec) and neither do we charge Tooling if the prototype (Standard Spec) is reordered for Production (Standard Spec).

 

4.If you only have a minor change in my design, do we charge Tooling NRE?

A:When you make any change to your printed circuit board, we assign it completely new tooling. This helps prevent old artwork or cnc programming from being used. Even a minor change will require the same process as new files, so a tooling charge may apply. Please contact your salesperson for details.  

 

5.Are your "Prototype" PCBs processed differently from your Custom Spec PCBs?

A:No. Our Standard Spec ("prototype") use the same premier manufacturing processes as our production(Custom Spec) circuit boards.  

 

6.To what acceptability standards do we build?

A: IPC A600 Class 2 through IPC 6012 Class 3A

 

7.Where should you send your files to get a printed circuit board quote or place an order?

A: You can simply send us an inquiry via Alibaba site. Very soon our sales person will contact you for your inquiry/files. Or you can send your inquiry/files to our email address

 

Contacts

Tel: +86-0755-29621535 EXT 810

Email: sales9@xdpcba.com

Skype: xingdapcbsales9

Website: www.xdpcba.com

        www.xdxpcb.com

 




Hot Tags: fr4 94v0 printed circuit board pcb, China, manufacturers, suppliers, factory, customized, OEM, ODM
Feedback